If you are wondering how to fix a faulty latch on a screen door, then this article will guide you through the process. There may be time when the latch will pop back open or will not close fully all the way. It may be either the latch plate is placed at a doorjamb in a wrong position. You do not need to remove the Security Screen in Adelaide, but get this rectified to prevent the latch plates from shifting in due time and due to heat expansion. If you find that the misaligned latch plate on door latch, you will have to adjust the latch plate on mortise.
Measure the Distance
If you find that the latch is loose, then you need to put the screws tightly, using a screwdriver on the hinges so that the screen door latch shuts properly once again. You may put the masking tape over the latch plate. You may rub any colored chalk on the door latch, for making proper marks and then test the door with Security Screen in Adelaide by shutting and then opening it. In the end, check the masking tape to see the spot where the door latch hits the tape following the colored chalk marks. With this process you will come to know the distance through which you will need to move the latch plate.
Raising the Door
Measure the distance through which the hole on the latch plate needs to be moved. If this distance is less than one-eighth of an inch then you can easily resolve the door-latch issue by using a half round file to make the hole in the latch plate larger. In case, you need to rise the entire Security Screen in Adelaide door to align the latch along with the latch plate hole you will need to remove the screw from the top hinge on the doorjamb. Put in a three inch in the space for the hinge screw of the doorjamb. On the reverse if you have to put the door at a lower angle, for a proper alignment, you will have to do the same with the hinge screw at the bottom.
Widening the Mortise
You may also need to widen the latch plate mortise to adjust the shallow hole in which the latch plate sits onto the doorjamb. You can use a half-round chisel for this matter. Make sure you measure the distance properly through which the latch plate needs to be moved. For this mark the position from the end of the latch plate mortise to the doorjamb with a pencil. Chip away the wood with a hammer as well as tap the chisel against the mortise edge to widen it to the desired level and continue doing it till the mortise edge reaches the pencil mark.
The Materials Required
You will need minimal materials to fix the latch on your Security Screen door in Adelaide. You will need a screwdriver, a 3-inch long wood screw, masking tape, vice, colored chalk, a half round file, a pencil and a drill. To read more Click Here
Measure the Distance
If you find that the latch is loose, then you need to put the screws tightly, using a screwdriver on the hinges so that the screen door latch shuts properly once again. You may put the masking tape over the latch plate. You may rub any colored chalk on the door latch, for making proper marks and then test the door with Security Screen in Adelaide by shutting and then opening it. In the end, check the masking tape to see the spot where the door latch hits the tape following the colored chalk marks. With this process you will come to know the distance through which you will need to move the latch plate.
Raising the Door
Measure the distance through which the hole on the latch plate needs to be moved. If this distance is less than one-eighth of an inch then you can easily resolve the door-latch issue by using a half round file to make the hole in the latch plate larger. In case, you need to rise the entire Security Screen in Adelaide door to align the latch along with the latch plate hole you will need to remove the screw from the top hinge on the doorjamb. Put in a three inch in the space for the hinge screw of the doorjamb. On the reverse if you have to put the door at a lower angle, for a proper alignment, you will have to do the same with the hinge screw at the bottom.
Widening the Mortise
You may also need to widen the latch plate mortise to adjust the shallow hole in which the latch plate sits onto the doorjamb. You can use a half-round chisel for this matter. Make sure you measure the distance properly through which the latch plate needs to be moved. For this mark the position from the end of the latch plate mortise to the doorjamb with a pencil. Chip away the wood with a hammer as well as tap the chisel against the mortise edge to widen it to the desired level and continue doing it till the mortise edge reaches the pencil mark.
The Materials Required
You will need minimal materials to fix the latch on your Security Screen door in Adelaide. You will need a screwdriver, a 3-inch long wood screw, masking tape, vice, colored chalk, a half round file, a pencil and a drill. To read more Click Here
No comments:
Post a Comment